How to Fix a Running Toilet: Step-by-Step Guide
A toilet that keeps running is one of the most common household plumbing problems, and learning how to fix a running toilet yourself is easy. In most homes the cause is a worn rubber part inside the tank that costs a few dollars. This guide shows you how to find the cause in a few minutes, fix it step by step, and know when it is time to call a plumber. For more on how toilets use water, see the EPA’s page on residential toilets.
Key takeaways
- Most running toilets are caused by a worn flapper, a misadjusted chain, or a faulty fill valve.
- A food coloring test takes about 10 minutes and tells you if the flapper is leaking into the bowl.
- The EPA WaterSense program says a worn flapper can silently leak thousands of gallons a year.
- Most fixes take an hour or less and cost under $20 in parts, according to Family Handyman.
- Call a plumber if the water keeps running after you replace the flapper and fill valve, or if you see cracks or leaks around the base.
How to fix a running toilet: how the tank works
Knowing four parts makes the repair far easier. Lift the tank lid and you will see them.
- Flush lever and chain: pulling the handle lifts the flapper through a chain.
- Flapper: a rubber seal at the bottom of the tank. It lifts to release water into the bowl, then drops to seal the opening again.
- Fill valve: the tall assembly that refills the tank after each flush and shuts off when a float says the tank is full.
- Overflow tube: the open vertical pipe in the middle of the tank. It sends excess water down to the bowl so the tank cannot spill onto your floor.
Why is my toilet running?
Two things can go wrong: water leaks from the tank into the bowl, or the fill valve never fully shuts off. Here are the usual causes, from most to least likely.
| Symptom | Likely cause | Fix |
|---|---|---|
| Water trickles into the bowl, tank refills every so often (ghost flushing) | Worn or dirty flapper, or a flapper that does not seal | Clean or replace the flapper |
| Water runs constantly, handle feels loose | Chain too long, too short or tangled | Adjust chain slack |
| Hissing or running sound, water flows into the overflow tube | Water level too high, or worn fill valve | Adjust float, or replace fill valve |
| Water keeps running after flapper was replaced | Worn flush valve seat or cracked overflow tube | Clean seat, or call a plumber |
| Hissing only when tank is refilling | Normal fill sound | No action needed |
Before you fix a running toilet
- Time: about an hour or less for most repairs.
- Tools: pliers, a sponge or old towel, a hacksaw (only if you must shorten the overflow tube), and a stick or pencil for testing.
- Parts you may need: a flapper, a fill valve, and a replacement fill tube.
- Water shutoff: find the small valve on the wall or floor behind the toilet. Turning it clockwise stops the water supply to the tank.
Step 1: Find the cause with a dye test
- Remove the tank lid and set it somewhere safe where it will not get knocked over.
- Flush once and watch the parts move. Listen for hissing or gurgling.
- Add a few drops of food coloring to the tank water. Do not flush.
- Wait about 10 minutes. The EPA says that if color shows up in the bowl, you have a leak. Some guides suggest waiting up to 20 minutes for slow leaks.
- Flush right away afterward so the dye does not stain the tank.
If the color appears in the bowl, the flapper is leaking. Go to Step 2. If the bowl stays clear but the toilet keeps running, the fill valve is the likely culprit. Go to Step 4.
Step 2: Check the chain and flapper
Press down gently on the flapper with a stick while the tank is refilling. If the water stops running, the flapper is not sealing properly.
- Check the chain first. It should have a little slack, about half an inch. If it is too tight, it holds the flapper open. If it is too loose or tangled, it can slip under the flapper and block it.
- Wipe the flapper and its seat. Mineral buildup or grit can stop a good flapper from sealing.
- Look for wear. A flapper that is warped, cracked, slimy or soft is done.
Step 3: Replace the flapper
The EPA says a flapper should be checked periodically and replaced at least every five years. It also advises bringing the old flapper, or a photo of it, to the store, and checking the width and whether it has a foam float that also needs replacing.
- Turn off the water at the shutoff valve.
- Flush to drain most of the water out of the tank.
- Unhook the chain from the lever and take the flapper off its pegs or ring.
- Install the new flapper of the same type, snapping it on the same attachment points.
- Hook the chain to the lever with about half an inch of slack.
- Turn the water back on, let the tank fill and flush two or three times to test.
Step 4: Adjust the water level and float
If the flapper is fine, check how high the water rises. The water should stop below the top of the overflow tube. Family Handyman suggests it should stop about half an inch to an inch under the top of the tube. Many modern tanks also have a mark on the inside showing the correct water line.
- Float cup valve: look for a small adjustment screw or clip on the valve. Turn the screw or slide the clip down to lower the water level.
- Ball float valve: older toilets have a float ball on a metal arm. Gently bend the arm down, or turn the screw at the valve end.
- Flush and check again. The tank should refill and the water should stop on its own.
Step 5: Replace the fill valve if it still runs
If lowering the float does not stop the hissing, the valve itself has probably worn out.
- Turn off the water and flush the tank. Soak up the last water with a sponge.
- Put a towel under the connection, then unscrew the water supply line from the bottom of the fill valve.
- Remove the locknut under the tank and lift out the old valve.
- Insert the new valve and tighten the locknut by hand, then a small additional turn with pliers. Overtightening can crack a porcelain tank.
- Reconnect the supply line and clip the fill tube to the overflow tube. Trim the tube so it sits at least half an inch above the water line.
- Set the valve height according to the instructions on its packaging, turn on the water and test.
Step 6: Check the overflow tube and flush valve seat
If the toilet still runs after a new flapper and fill valve, look at two things:
- Overflow tube height: if the water has to rise higher than the tube to shut off, the tube is too tall for the fill valve. Family Handyman describes cutting it with a hacksaw so it sits about an inch below the valve’s critical level mark.
- Flush valve seat: this is the ring the flapper rests on. Run your finger around it. If it feels rough, pitted or corroded, the flapper cannot seal no matter how new it is. Light buildup can be cleaned with a scouring pad. Heavy damage means replacing the flush valve or the toilet.
How much money can a running toilet waste?
The EPA WaterSense program estimates that household leaks waste nearly 1 trillion gallons of water nationwide every year, and the average home loses more than 9,300 gallons annually to leaks. About 9% of homes leak 50 gallons or more per day. A running toilet is one of the common culprits.
To estimate what a leak costs you, use this formula:
Gallons wasted per day × 30 × your price per gallon = monthly cost
Your water bill shows the price. Many bills list it per 1,000 gallons, so divide that price by 1,000 to get the price per gallon. For example, if your rate were $5 per 1,000 gallons ($0.005 per gallon) and a leak wasted 50 gallons a day, that would add up to about $7.50 a month. Your own rate and sewer charges will differ, but this shows why it pays to fix a leak quickly.
When to call a plumber
- The toilet keeps running after you replace the flapper and fill valve.
- You see cracks in the tank or bowl, or water pooling around the base.
- The shutoff valve does not turn or leaks when you try to close it.
- The flush valve seat is badly corroded or the flush valve needs replacing.
- You are not comfortable working with the supply line. A leak behind the toilet can damage a floor quickly.
How to prevent it from happening again
- Check the flapper once a year and replace it at least every five years, as the EPA advises.
- Do not use drop-in tablets with bleach or harsh chemicals in the tank. They can damage rubber parts over time.
- Run the dye test twice a year. It takes a minute to set up.
- Keep a spare flapper and fill valve in your toolbox.
- While you check your bathroom plumbing, clear slow drains too. See how to clean a shower drain.
Frequently asked questions
Why does my toilet run for a few seconds every so often?
This is called ghost flushing. Water slowly leaks from the tank into the bowl until the fill valve turns on to top it up. A worn flapper is the most likely cause.
How much does it cost to fix a running toilet?
Doing it yourself, Family Handyman puts the total at under $20 in parts. A plumber will charge more because of the service call and labor, and rates vary by area.
Can a running toilet make my water bill go up?
Yes. Even a slow leak adds up over weeks. Use the formula above to estimate the cost for your home.
Do I need to replace the whole toilet?
Rarely. Most causes are small inexpensive parts inside the tank. Replacement is usually only needed if the porcelain is cracked or the flush valve seat is badly damaged.
Is it okay to leave a running toilet until the weekend?
A short delay is not an emergency, but the water waste adds up. If the tank is overflowing or water is on the floor, turn off the shutoff valve right away.
Last updated November 18, 2026.