Checksum error: close-up of a green circuit board
|

What Is a Checksum Error? Causes and How to Fix It

A checksum error means a computer compared two values that should have matched and they did not. Something changed or was damaged along the way: a download, a file on your drive, or the settings your computer stores at startup. The good news is that the error itself is a protective check doing its job, and most cases have a simple fix. This guide explains what a checksum error is, how to tell which type you have, and how to fix each one step by step.

Key takeaways

  • A checksum is a small value calculated from data. If it does not match the expected value, the data has changed or is damaged, and you see a checksum error.
  • The most common one on a PC is the CMOS checksum error at startup. It is usually caused by a dead CR2032 coin-cell battery on the motherboard.
  • Checksum errors in downloads and archives (such as WinRAR or ZIP files) usually mean the file is incomplete or corrupted. Download it again.
  • A checksum only detects a problem. It cannot repair the data.
  • A message that names the BIOS firmware itself, such as “BIOS ROM checksum error”, points to damaged firmware and may need the manufacturer’s help.

What is a checksum?

A checksum is a short value that a program calculates from a block of data, such as a file, a network message or the settings stored on your motherboard. When the data is stored or sent, the checksum travels with it. Later, the computer calculates the checksum again and compares the two.

If they match, the data is almost certainly intact. If they differ, even a single changed bit can be enough, so the system reports a checksum error. Because the check is so sensitive, it catches damage that you would never notice by eye.

Where you see checksum errors

The message looks similar in different places, but the cause and the fix are different. Find your situation in this table first.

Where it appearsTypical messageMost likely causeJump to
PC startup screenCMOS checksum error – Defaults loadedDead or weak CMOS batteryFix 1
PC startup screenBIOS ROM checksum error or Main BIOS checksum errorDamaged BIOS firmwareFix 2
Extracting a ZIP, RAR or 7z fileChecksum error or corrupted archiveIncomplete or damaged downloadFix 3
Installing or verifying a downloadFile verification failed or checksum mismatchCorrupt download or wrong fileFix 3 and how to verify
Copying files or running a backupChecksum or data errorFailing drive, cable or memoryFix 4

Fix 1: CMOS checksum error at startup

Your motherboard keeps its BIOS settings, such as the date, time and boot order, in a small memory chip called CMOS. A coin-cell battery, usually a CR2032, keeps that chip powered when the computer is off. When the battery runs low, the stored settings become unreliable, the startup check fails and you see a message such as “CMOS checksum error – Defaults loaded”. The computer then falls back to default settings.

A common clue is that the error appears after the computer has been fully powered off or unplugged, but not after a normal restart.

  1. Restart and press the BIOS setup key shown on screen (often F2, F10 or Delete, depending on the manufacturer).
  2. Choose the option to load default settings (often labelled “Load Optimized Defaults” or “Load Setup Defaults”), then save and exit. On some HP computers this is F9 to load defaults and F10 to save.
  3. If the error comes back after a cold start, shut down and unplug the computer. If it is a desktop, open the case after touching bare metal to discharge static.
  4. Find the flat silver coin-cell battery on the motherboard. It is usually marked CR2032.
  5. Replace it with a new CR2032 of the same type.
  6. Power on, enter the BIOS and set the date, time and boot order again.

On many laptops the battery is harder to reach or attached with a small cable. If the computer is under warranty, it is usually better to let the manufacturer or a technician replace it than to risk damaging the machine.

If the error persists after a new battery, check the manufacturer’s support page for a BIOS update, and contact support if the machine is still under warranty.

Fix 2: BIOS ROM or Main BIOS checksum error

When the message names the firmware itself, the BIOS image stored on the chip is damaged, not just the settings. This can follow a failed or interrupted BIOS update or a hardware fault. A new battery will not fix it.

  • Check the manufacturer’s support site for a BIOS recovery procedure for your exact model. Many boards can restore the firmware from a USB drive.
  • Do not power off or interrupt a BIOS update once it starts.
  • If recovery fails, the board may need professional repair or replacement. Back up your data from the drive if you can.

Fix 3: Checksum error in a download or archive

Programs such as WinRAR, 7-Zip and many installers verify files as they open them. A checksum error here normally means that the file you downloaded is not identical to the original.

  1. Delete the damaged file and download it again from the official source.
  2. Use a stable connection and do not pause and resume large downloads. Try a different browser or network if it keeps failing.
  3. Make sure the drive has enough free space for the file and for extracting it.
  4. Try the download page’s mirror or alternative link if one is offered.
  5. Verify the new file’s checksum against the one published by the source (see the next section).

Some archive tools include a repair feature that can recover part of a damaged archive. Results vary, and downloading a clean copy is almost always faster and safer.

How to verify a file’s checksum yourself

Reputable software publishers list a checksum, usually SHA-256, next to the download. Calculate the same checksum on your copy and compare. If every character matches, the file is intact. Comparing ignores upper and lower case.

Windows PowerShell

The Get-FileHash command uses SHA-256 by default. It also supports SHA1, SHA384, SHA512 and MD5. Microsoft notes that MD5 and SHA1 are no longer considered secure against tampering, so use SHA-256 when it is offered.

Get-FileHash C:\Users\YourName\Downloads\setup.iso -Algorithm SHA256

Windows Command Prompt

certutil -hashfile C:\Users\YourName\Downloads\setup.iso SHA256

macOS Terminal

shasum -a 256 ~/Downloads/setup.dmg

Linux

sha256sum ~/Downloads/setup.iso

If the value does not match the published one, delete the file and download it again. If it still does not match, the source may have changed the file or you may be looking at the wrong checksum, so check you are on the official page.

Fix 4: Checksum errors from hardware problems

If checksum errors appear when copying files, restoring backups or opening files that used to work, the problem may be the hardware that stores or moves the data.

  • Check the drive. In Windows, open Command Prompt as administrator and run chkdsk C: /f. You may be asked to restart. Also look at the drive’s SMART health with the manufacturer’s tool.
  • Test the memory. Search for “Windows Memory Diagnostic” in the Start menu and run it. Faulty RAM can corrupt data before it is saved.
  • Swap cables and ports. A loose or damaged USB, SATA or network cable can introduce errors. Try another cable and another port.
  • Back up now. If a drive is failing, copy important files to another drive before running repairs.

Checksum vs. hash vs. CRC

These terms overlap and are often used loosely. In everyday use:

TermWhat it isTypical use
ChecksumA value used to detect accidental errors in dataGeneral error detection
CRC (cyclic redundancy check)A common, fast type of checksum that is good at catching transmission errorsZIP files, network packets, storage devices
Cryptographic hash (SHA-256)A longer value designed so that changes are practically impossible to hideVerifying downloads and detecting tampering

If the message you are seeing is specifically a CRC error, read our guide to what a CRC error is and how to fix it.

A checksum error means data does not match. It does not say how the data was changed, and it cannot fix the data.

When to worry

  • The error returns after a new battery, a BIOS reset and a BIOS update.
  • Several different files fail checksum checks, or backups keep failing.
  • The drive makes clicking sounds or becomes very slow.
  • The computer will not start and the message names the BIOS ROM.

In those cases, copy your important data somewhere safe first, then contact the manufacturer or a repair technician.

Frequently asked questions

Is a checksum error caused by a virus?

Usually not. Most checksum errors come from a dead CMOS battery or a damaged download. Malware can modify files, but a checksum error alone is not a sign of infection. If you are worried, run a scan with your security software.

Can I ignore a CMOS checksum error?

You can usually keep using the computer after it loads defaults, but ignoring it means your date, time and custom BIOS settings reset every time power is lost. The battery is cheap to replace, so it is best to fix it.

Why does the error only appear after I unplug the computer?

The CMOS battery keeps settings alive only when mains power is off. If the battery is dead, a restart looks fine because the power supply keeps the chip alive, but a full power-off wipes it.

How long does a CMOS battery last?

A CR2032 usually lasts several years, and a few years is typical for a computer in regular use. Computers kept unplugged for long periods may drain it faster.

What does “checksum mismatch” mean?

It means the checksum you calculated is different from the one you expected. The file is not identical to the original, so download it again.

Can a checksum error be repaired?

Not by the checksum itself. A checksum only detects errors. Fixing the problem means replacing the corrupted data, such as downloading again, restoring from a backup or replacing faulty hardware.

Last updated November 18, 2026.

Related guides